EAL
Level 3
QN: 600/9793/0
Curriculum Active
EAL Level 3 NVQ Diploma in Engineering Technical Support
Official qualification regulated by Ofqual, awarded by EAL. Classified as a Occupational Qualification. Total guided learning hours: 11920 hours.
Qualification Level
Level 3
Awarding Body
EAL
Syllabus Units
73 Units
Guided Hours
11920 hrs
Instant access to interactive lessons, quizzes, and spaced revision.
Course Syllabus & Study Modules
Complete breakdown of verified curriculum topics and learning objectives.
1
Analysing and Interpreting the Results of Radiographic Tests
Verified
Key Learning Objectives:
- Analyse and interpret the results of radiographic tests
- Know how to analyse and interpret the results of radiographic tests
2
Carrying Out Fault Diagnosis on Engineering Plant and Equipment
Verified
Key Learning Objectives:
- Carry out fault diagnosis on engineering plant and equipment
- Know how to carry out fault diagnosis on engineering plant and equipment
3
Carrying Out Health and Safety Risk Assessments on Engineering Activities
Verified
Key Learning Objectives:
- Carry out health and safety risk assessments on engineering activities
- Know how to carry out health and safety risk assessments on engineering activities
4
Carrying Out Project Management of Engineering Activities
Verified
Key Learning Objectives:
- Carry out project management of engineering activities
- Know how to carry out project management of engineering activities
5
Carrying Out Visual Inspection of Welded Fabrications
Verified
Key Learning Objectives:
- Carry out visual inspection of welded fabrications
- Know how to carry out visual inspection of welded fabrications
6
Checking and Calibrating Electrical and Electronic Test Equipment
Verified
Key Learning Objectives:
- Check and calibrate electrical and electronic test equipment
- Know how to check and calibrate electrical and electronic test equipment
7
Checking and Calibrating Mechanical Inspection Equipment
Verified
Key Learning Objectives:
- Check and calibrate mechanical inspection equipment
- Know how to check and calibrate mechanical inspection equipment
8
Checking and Calibrating Process Control Instrumentation
Verified
Key Learning Objectives:
- Check and calibrate process control instrumentation
- Know how to check and calibrate process control instrumentation
9
Complying with statutory regulations and organisational safety requirements
Verified
Key Learning Objectives:
- Comply with statutory regulations and organisational safety requirements
- Know how to comply with statutory regulations and organisational safety requirements
10
Determining Engineering Requirements for the Supply of Products or Services
Verified
Key Learning Objectives:
- Determine engineering requirements for the supply of products or services
- Know how to determine engineering requirements for the supply of products or services
11
Determining Engineering Software Requirements
Verified
Key Learning Objectives:
- Determine engineering software requirements
- Know how to determine engineering software requirements
12
Determining Technical Requirements for Non-Destructive Testing
Verified
Key Learning Objectives:
- Determine technical requirements for non-destructive testing
- Know how to determine technical requirements for non-destructive testing
13
Developing and Maintaining Effective Customer Relationships
Verified
Key Learning Objectives:
- Develop and maintain effective customer relationships
- Know how to develop and maintain effective customer relationships
14
Handing Over and Exchanging Responsibility for Control of Engineering Activities
Verified
Key Learning Objectives:
- Hand over and exchange responsibility for control of engineering activities
- Know how to hand over and exchange responsibility for control of engineering activities
15
Implementing Engineering Activities
Verified
Key Learning Objectives:
- Implement engineering activities
- Know how to implement engineering activities
16
Implementing Quality Control Systems and Procedures in an Engineering Environment
Verified
Key Learning Objectives:
- Implement quality control systems and procedures in an engineering environment
- Know how to implement quality control systems and procedures in an engineering environment
17
Inspecting and Testing Electrical Products
Verified
Key Learning Objectives:
- Inspect and test electrical products
- Know how to inspect and test electrical products
18
Inspecting and Testing Electronic Products
Verified
Key Learning Objectives:
- Inspect and test electronic products
- Know how to inspect and test electronic products
19
Inspecting Components using Co-ordinate Measuring Machines _CMM_
Verified
Key Learning Objectives:
- Inspect components using co-ordinate measuring machines (CMM)
- Know how to inspect components using co-ordinate measuring machines (CMM)
20
Inspecting Engineering Products by Magnetic Particle Testing
Verified
Key Learning Objectives:
- Inspect engineering products by magnetic particle testing
- Know how to inspect engineering products by magnetic particle testing
21
Inspecting Engineering Products by Penetrant Flaw Detection Techniques
Verified
Key Learning Objectives:
- Inspect engineering products by penetrant flaw detection techniques
- Know how to inspect engineering products by penetrant flaw detection techniques
22
Inspecting Engineering Products using Ultrasonic Testing Techniques
Verified
Key Learning Objectives:
- Inspect engineering products using ultrasonic testing techniques
- Know how to inspect engineering products using ultrasonic testing techniques
23
Inspecting Fabricated Components and Structures
Verified
Key Learning Objectives:
- Inspect fabricated components and structures
- Know how to inspect fabricated components and structures
24
Loading and Proving Computer Control Programs
Verified
Key Learning Objectives:
- Load and prove computer control programs
- Know how to load and prove computer control programs
25
Monitoring Engineering Activities
Verified
Key Learning Objectives:
- Monitor engineering activities
- Know how to monitor engineering activities
26
Obtaining Resources for Engineering Activities
Verified
Key Learning Objectives:
- Obtain resources for engineering activities
- Know how to obtain resources for engineering activities
27
Performing Computer System Security Assessments for Engineering Software
Verified
Key Learning Objectives:
- Perform computer system security assessments for engineering software
- Know how to perform computer system security assessments for engineering software
28
Performing Engineering Software Acquisition
Verified
Key Learning Objectives:
- Perform engineering software acquisition
- Know how to perform engineering software acquisition
29
Performing Engineering Software Analysis Techniques
Verified
Key Learning Objectives:
- Perform engineering software analysis techniques
- Know how to perform engineering software analysis techniques
30
Performing Low Level Programming for Engineering Software
Verified
Key Learning Objectives:
- Perform low level programming for engineering software
- Know how to perform low level programming for engineering software
31
Preparing Ultrasonic Flaw Detection Equipment for Testing Activities
Verified
Key Learning Objectives:
- Prepare ultrasonic flaw detection equipment for testing activities
- Know how to prepare ultrasonic flaw detection equipment for testing activities
32
Producing Contractual Arrangements to Supply or Procure Goods or Services for Engineering Activities
Verified
Key Learning Objectives:
- Produce contractual arrangements to supply or procure goods or services for engineering activities
- Know how to produce contractual arrangements to supply or procure goods or services for engineering activities
33
Producing Electrical Engineering Drawings using Computer Aided Techniques
Verified
Key Learning Objectives:
- Produce electrical engineering drawings using computer aided techniques
- Know how to produce electrical engineering drawings using computer aided techniques
34
Producing Electronic Engineering Drawings using Computer Aided Techniques
Verified
Key Learning Objectives:
- Produce electronic engineering drawings using computer aided techniques
- Know how to produce electronic engineering drawings using computer aided techniques
35
Producing Engineering Drawings/Models using 3D Computer Aided Techniques
Verified
Key Learning Objectives:
- Produce engineering drawings/models using 3D computer aided techniques
- Know how to produce engineering drawings/models using 3D computer aided techniques
36
Producing Engineering Software Implementation
Verified
Key Learning Objectives:
- Produce engineering software implementation
- Know how to produce engineering software implementation
37
Producing Mechanical Engineering Drawings using Computer Aided Techniques
Verified
Key Learning Objectives:
- Produce mechanical engineering drawings using computer aided techniques
- Know how to produce mechanical engineering drawings using computer aided techniques
38
Producing Off-line Programs for NC/CNC Boring Machines
Verified
Key Learning Objectives:
- Produce off-line programs for NC/CNC boring machines
- Know how to produce off-line programs for NC/CNC boring machines
39
Producing Off-line Programs for NC/CNC Fabrication Machines
Verified
Key Learning Objectives:
- Produce off-line programs for NC/CNC fabrication machines
- Know how to produce off-line programs for NC/CNC fabrication machines
40
Producing Off-line Programs for NC/CNC Gear Cutting Machines
Verified
Key Learning Objectives:
- Produce off-line programs for NC/CNC gear cutting machines
- Know how to produce off-line programs for NC/CNC gear cutting machines
41
Producing Off-line Programs for NC/CNC Grinding Machines
Verified
Key Learning Objectives:
- Produce off-line programs for NC/CNC grinding machines
- Know how to produce off-line programs for NC/CNC grinding machines
42
Producing Off-line Programs for NC/CNC Machining Centres
Verified
Key Learning Objectives:
- Produce off-line programs for NC/CNC machining centres
- Know how to produce off-line programs for NC/CNC machining centres
43
Producing Off-line Programs for NC/CNC Turning Machines
Verified
Key Learning Objectives:
- Produce off-line programs for NC/CNC turning machines
- Know how to produce off-line programs for NC/CNC turning machines
44
Producing Off-line Programs for Programmable Logic Controller Equipment
Verified
Key Learning Objectives:
- Produce off-line programs for programmable logic controller equipment
- Know how to produce off-line programs for programmable logic controller equipment
45
Producing Operating Programs for Co-ordinate Measuring Machines _CMM_
Verified
Key Learning Objectives:
- Produce operating programs for co-ordinate measuring machines (CMM)
- Know how to produce operating programs for co-ordinate measuring machines (CMM)
46
Scheduling Engineering Activities
Verified
Key Learning Objectives:
- Schedule engineering activities
- Know how to schedule engineering activities
47
Supporting logistics operations in an engineering manufacturing environment
Verified
Key Learning Objectives:
- Supporting logistics operations in an engineering manufacturing environment
- Know how to support logistics operations in an engineering manufacturing environment
48
Testing Engineering Software
Verified
Key Learning Objectives:
- Test engineering software
- Know how to test engineering software
49
Using and Maintaining Business Procedures and Protocols in an Engineering Environment
Verified
Key Learning Objectives:
- Use and maintain business procedures and protocols in an engineering environment
- Know how to use and maintain business procedures and protocols in an engineering environment
50
Working efficiently and effectively in engineering
Verified
Key Learning Objectives:
- Work efficiently and effectively in engineering
- Know how to work efficiently and effectively in engineering
Regulatory & Verification Details
- Qualification Number (QN)
- 600/9793/0
- Regulated Status
- Available to learners
- Awarding Body
- EAL
- Qualification Type
- Occupational Qualification
- Operational Start
- Jul 2013