Skip to topic
    ← Back to course topics

    Communication basics — AQA A-Level Computer Science

    Communication basics covers the foundational methods used to transmit data across networks, including serial versus parallel transmission, synchronous versus asynchronous communication, and the relationship between baud rate and bit rate. Understanding these mechanisms is essential for mastering how digital devices reliably exchange binary signals over physical and logical transmission media.

    Communication basics explained

    Section 4.9.1.2 covers the communication basics used to describe network performance.

    Read the full explanation

    Baud rate is the number of signal changes (symbols) per second, so a system sending 2 symbols per second has a baud rate of 2; bit rate is the number of bits transmitted per second, and where each symbol carries several bits the bit rate exceeds the baud rate. Bandwidth is the range of frequencies a channel can carry, measured in hertz, and in digital contexts the maximum data rate a link can sustain, in bits per second. Latency is the delay between sending and receiving data, made up of transmission, propagation, processing and queuing delays. A definition should state the category and distinguishing feature, with correct units.

    What to demonstrate

    1. Defines baud rate as the number of signal changes or symbols transmitted per second, not the number of bits.
    2. Defines bit rate as the number of bits transmitted per second, distinguishing it from baud rate where a symbol carries multiple bits.
    3. Defines bandwidth as the range of frequencies a channel can carry (hertz), or the maximum data rate of a link in bits per second.
    Show all 5 objectives
    1. Defines latency as the delay between transmission and reception, including propagation, transmission, processing and queuing components.
    2. Uses correct units: baud and bits per second, hertz for frequency bandwidth.

    Which command word is this?

    Set out purposes or reasons with logical progression. State 'what' occurs and 'why' or 'how' it happens (e.g., explaining how clock drift is mitigated in asynchronous communication).

    Communication basics exam tips

    Topic Overview

    Communication basics examines the fundamental principles governing how binary data travels between hardware components and across networks. It covers transmission modes (serial and parallel), transmission timing (synchronous and asynchronous), and metrics that measure performance including baud rate, bit rate, latency, and bandwidth.

    This topic forms the foundational layer for all networking, internet technologies, and internal bus architectures within AQA A-Level Computer Science. Mastering these concepts enables students to evaluate trade-offs in hardware interconnects like USB and PCIe versus external telecommunication systems.

    Key Concepts
    • →Serial vs Parallel: Serial sends data bit-by-bit over a single channel; parallel sends multiple bits concurrently along separate physical tracks.
    • →Synchronous vs Asynchronous: Synchronous relies on a coordinated clock signal or embedded timing pulse; asynchronous frames data characters with start, stop, and parity bits without a continuous shared clock.
    • →Baud Rate vs Bit Rate: Baud rate represents symbol state transitions per second, whereas bit rate measures transmitted bits per second (Bit Rate = Baud Rate * bits per symbol).
    • →Bandwidth and Latency: Bandwidth defines the theoretical data-carrying capacity of a medium (in Hz or bps); latency represents the delay between transmission and receipt.
    Marking Points
    • Defines baud rate as the number of signal changes or symbols transmitted per second, not the number of bits.
    • Defines bit rate as the number of bits transmitted per second, distinguishing it from baud rate where a symbol carries multiple bits.
    • Defines bandwidth as the range of frequencies a channel can carry (hertz), or the maximum data rate of a link in bits per second.
    • Defines latency as the delay between transmission and reception, including propagation, transmission, processing and queuing components.
    • Uses correct units: baud and bits per second, hertz for frequency bandwidth.
    Examiner Tips
    • 💡Lead each definition with the category (a rate, a range of frequencies, a delay) then the distinguishing feature.
    • 💡State units explicitly: symbols per second, bits per second, hertz, seconds or milliseconds.
    • 💡For a calculation, remember bit rate = baud rate × bits per symbol.
    • 💡Keep each definition to one precise sentence before adding any example.
    • 💡Always state the mathematical relationship between signal states and bits: if an exam question states 'M signal levels', show that bits per symbol = log2(M).
    • 💡When explaining asynchronous transmission framing overhead, remember that the start bit, stop bit(s), and optional parity bit are transmission overhead and do not carry payload data.
    Common Mistakes
    • Treating baud rate and bit rate as identical; they coincide only when one bit is sent per symbol.
    • Giving bandwidth only in bits per second when the frequency-range meaning in hertz is required.
    • Describing latency as the volume of data or the speed of the link rather than the delay incurred.
    • Offering an example instead of a definition; state the category and distinguishing feature first.
    • Assuming parallel transmission is always faster than serial: While parallel transmits multiple bits simultaneously, timing skew and crosstalk drastically limit its clock frequency over distances greater than a few centimeters, making high-frequency serial interfaces (e.g., PCIe, SATA, USB) significantly faster in modern hardware.
    • Confusing bandwidth with data transfer speed: Bandwidth measures width or channel capacity (volume of data per second), whereas propagation speed or latency determines how fast an individual signal traverses the medium.
    Revision Plan
    1. 1Day 1-2: Master the exact definitions of serial, parallel, synchronous, and asynchronous transmission, creating comparative summary tables.
    2. 2Day 3-4: Practice mathematical calculations linking baud rate, bit states, and overall bit rate using log2 rules.
    3. 3Day 5-6: Diagram asynchronous frames, labeling start bits, payload, parity, and stop bits, and explain why skew and crosstalk limit parallel communication.
    4. 4Day 7: Work through past AQA exam questions under timed conditions and review against official mark schemes.
    Exam Question Types
    • 📋Definition and differentiation questions (e.g., 'Compare synchronous and asynchronous transmission' [4 marks]). Focus on clock signals vs start/stop bits.
    • 📋Calculation questions requiring students to calculate bit rate given baud rate and signal voltage levels [2-3 marks].
    • 📋Scenario-based evaluation questions (e.g., recommending serial or parallel transmission for a specified peripheral connection over a stated distance) [4-6 marks].
    Command Word Expectations (AQA)
    Explain

    Set out purposes or reasons with logical progression. State 'what' occurs and 'why' or 'how' it happens (e.g., explaining how clock drift is mitigated in asynchronous communication).

    Compare

    Identify both similarities and differences between two concepts (e.g., serial vs parallel), explicitly drawing direct parallels rather than describing each in isolation.

    Calculate

    Perform numerical operations to arrive at an answer. Show all working clearly and include correct measurement units (e.g., bps, kbps, baud).

    How Students Lose Marks (Examiner Pitfalls)
    Pitfall: Confusing baud rate with bit rate, or assuming they are always numerically identical.
    ❌ Weak Answer (Loses Marks):Baud rate is how many bits are sent per second along a wire.
    Example improved answer:Baud rate is the number of signal changes per second on a communication channel. Bit rate is the number of bits transferred per second. Bit rate equals the baud rate multiplied by the number of bits encoded per signal change.
    Examiner Tip: Always state that baud rate measures signal transitions (symbols) per second, not bits, and recall that bit rate can exceed baud rate if multi-level signaling (modulation) is used.
    Pitfall: Vague explanations of why parallel transmission suffers over long distances, omitting terms like skew and crosstalk.
    ❌ Weak Answer (Loses Marks):Parallel transmission gets messed up over long distances because wires interfere with each other and data arrives at different times.
    Example improved answer:Parallel transmission suffers from data skew, where bits travel at marginally different speeds along individual physical lines and arrive out of synchronization. It also suffers from crosstalk, where electromagnetic interference between adjacent tightly packed wires corrupts transmitted bits.
    Examiner Tip: Use the precise technical terms 'skew' and 'crosstalk' whenever comparing serial and parallel transmission across longer physical distances.
    Step-by-Step Worked Solutions

    Question: A communication channel operates at a baud rate of 4800 baud. Each signal state represents one of 16 distinct voltage levels. Calculate the bit rate of the channel.

    1. 1.Step 1: Determine the number of bits that can be represented by 16 distinct signal levels using the formula n = log2(levels). log2(16) = 4 bits per signal change.
    2. 2.Step 2: Apply the relationship formula: Bit rate = Baud rate * Number of bits per signal change.
    3. 3.Step 3: Multiply the values: 4800 baud * 4 bits/signal = 19200 bits per second (bps).
    Final Answer: 19,200 bps (or 19.2 kbps)

    Question: Explain the role of start and stop bits in asynchronous serial data transmission and describe how the receiver synchronizes its internal clock.

    1. 1.Step 1: Identify the baseline idle state of an asynchronous transmission line (typically logic high / 1).
    2. 2.Step 2: Explain the start bit: The transmitter sends a start bit (a drop to logic 0) to notify the receiver that a byte of data follows, triggering the receiver's local clock to start.
    3. 3.Step 3: Explain the stop bit: One or two stop bits (return to logic 1) follow the payload bits to indicate the frame's end and ensure line recovery before another start bit arrives.
    4. 4.Step 4: Conclude on synchronization: The receiver synchronizes its clock only for the duration of the single character frame, eliminating the need for a persistent shared clock signal.
    Final Answer: Start bits alert the receiver and synchronize its clock at the beginning of each frame; stop bits confirm frame completion and reset line idle state, allowing independent, unsynchronized clocks.
    Active Recall Memory Test
    What is the formula linking bit rate, baud rate, and number of signal states (L)?
    Key Fact: Bit rate = Baud rate * log2(L).
    Define 'crosstalk' in the context of data communication.
    Key Fact: Electromagnetic interference between adjacent wires or transmission paths that distorts or corrupts data signals.
    Why are start and stop bits required in asynchronous transmission?
    Key Fact: To synchronize the receiver's local clock at the start of a frame and signal when the character payload has finished, avoiding clock drift.
    What physical problem causes data skew in parallel transmission?
    Key Fact: Minor variations in wire length, impedance, or material properties that cause bits sent simultaneously to arrive at slightly different times.
    Frequently Asked Questions
    Why is serial transmission preferred over parallel for modern high-speed connections?
    Although parallel transmission sends multiple bits simultaneously, it suffers from signal skew (bits arriving at slightly different times) and crosstalk (electromagnetic interference between adjacent lines). These physical limitations prevent parallel channels from operating at ultra-high clock frequencies over practical distances. Modern serial interfaces avoid skew entirely, allowing dramatically higher clock speeds that produce a superior overall bit rate.
    Can bit rate ever be lower than baud rate?
    No. In digital communications, every signal change must encode at least one bit or represent part of a synchronization state. If each signal change encodes one bit, the bit rate equals the baud rate. If modulation techniques encode multiple bits per signal state, the bit rate exceeds the baud rate.
    What is parity checking and where does the parity bit go in asynchronous transmission?
    A parity bit is an error-detection bit appended immediately after the data payload bits and before the stop bit in an asynchronous frame. The transmitter sets the bit to 0 or 1 to make the total count of 1s either even (even parity) or odd (odd parity). If noise flips a single bit during transit, the receiver detects a mismatch in the parity count.
    What is the key difference between latency and propagation delay?
    Propagation delay is a specific component of latency, describing the time it takes for a single bit to travel physically through a medium at the speed of light or copper signal velocity. Latency is the broader measurement encompassing total delay, including propagation delay, transmission serialization delay, processing delay at nodes, and queuing delays in network buffers.