Required practicals — AQA GCSE Chemistry
The 8 required practicals on this course, as named in its specification.
Required practical 1: preparation of a pure, dry sample of a soluble salt from an insoluble oxide or carbonate using a Bunsen burner to heat dilute acid and a water bath or electric heater to evaporate the solution.
In this required practical, warm dilute acid using a Bunsen burner, then add the insoluble oxide or carbonate a little at a time until it is in excess and no more dissolves. Filter the mixture to remove the excess solid, keeping the filtrate, which contains the soluble salt. Evaporate the filtrate using a water bath or electric heater rather than a direct flame, because gentle heating avoids spitting and decomposition. Stop when crystals begin to appear, then cool, filter, wash with a little cold distilled water and dry gently. The practical develops safe heating, filtration and crystallisation skills while producing a pure, dry named salt such as copper(II) sulfate or magnesium sulfate.
Revise Soluble saltsRequired practical 2: (chemistry only) determination of the reacting volumes of solutions of a strong acid and a strong alkali by titration.
In this required practical you find the volume of one solution that exactly reacts with a known volume of another. A strong acid, such as hydrochloric acid, is placed in a burette and a measured volume of strong alkali, such as sodium hydroxide solution, is pipetted into a conical flask with a few drops of indicator. You record the initial burette reading, then add acid steadily while swirling, slowing near the end point as the indicator colour changes. Repeating until concordant titres agree improves reliability. You must use accurate procedural techniques, such as rinsing the burette with the acid and reading the bottom of the meniscus at eye level, to ensure precise volume measurements.
Revise Titrations (chemistry only)Required practical 3: investigate what happens when aqueous solutions are electrolysed using inert electrodes. This should be an investigation involving developing a hypothesis.
In this practical, you electrolyse different aqueous solutions using inert electrodes such as graphite and observe the products at each electrode. You develop a hypothesis linking the ions present to the products, for example that a solution containing halide ions will produce a halogen at the anode. You then test the hypothesis by electrolysing solutions such as sodium chloride, copper chloride and sodium sulfate, recording observations at the cathode and anode. Observations may include gas bubbles, colour changes, litmus or indicator tests, and identification of gases. You evaluate whether results support the hypothesis and explain any anomalies using ion discharge rules.
Revise Electrolysis of aqueous solutionsRequired practical 4: investigate the variables that affect temperature changes in reacting solutions such as, eg acid plus metals, acid plus carbonates, neutralisations, displacement of metals.
In Required practical 4, you investigate variables that affect temperature changes in reacting solutions. Suitable reactions include acid plus metals, acid plus carbonates, neutralisation and displacement of metals. You measure the temperature change of the solution before and after reaction, then vary one factor at a time, such as concentration, volume, particle size or the metal used. For example, react different concentrations of hydrochloric acid with magnesium and record the maximum temperature rise. Control other variables to make the comparison fair. The practical develops skills in measuring temperature, controlling variables, recording data and drawing conclusions about energy transfer.
Revise Energy transfer during exothermic and endothermic reactionsRequired practical 5: investigate how changes in concentration affect the rates of reactions by a method involving measuring the volume of a gas produced and a method involving a change in colour or turbidity.
In this practical you change the concentration of a reactant and measure how fast the reaction proceeds. In the gas-volume method, a suitable reaction such as magnesium with dilute hydrochloric acid produces hydrogen; you collect the gas in a syringe or inverted measuring cylinder and record the volume at regular time intervals. The initial gradient of a volume-time graph gives a measure of rate. In the colour or turbidity method, a reaction such as sodium thiosulfate with dilute hydrochloric acid produces a pale yellow precipitate of sulfur; you time how long a black cross viewed through the mixture takes to disappear. A shorter time means a faster rate. In both methods, control variables such as temperature, volume and concentration of the other reactant must be kept constant for a fair comparison.
Revise Factors which affect the rates of chemical reactionsRequired practical 6: investigate how paper chromatography can be used to separate and tell the difference between coloured substances. Students should calculate R values.
Paper chromatography separates coloured substances by allowing a solvent to move up paper, carrying dissolved dyes at different rates. A pencil baseline is drawn near the bottom, small spots of known dyes and an unknown mixture are applied, and the paper is lowered into solvent so the baseline stays above the liquid. As solvent rises, components partition between mobile and stationary phases and separate. The distance each spot travels relative to the solvent front gives its Rf value. Comparing Rf values and spot colours identifies components in an unknown mixture. For example, a purple ink may separate into red and blue spots matching known dyes.
Revise ChromatographyRequired practical 7: use of chemical tests to identify the ions in unknown single ionic compounds covering the ions from sections Flame tests (page 73) to Sulfates (page 74).
This required practical brings together the qualitative tests for positive and negative ions in single ionic compounds. You dissolve or moisten the unknown compound, then select tests that reveal its ions: flame tests for metal cations such as lithium, sodium, potassium, calcium and copper; sodium hydroxide solution for metal cations that form coloured or white precipitates; dilute acid with silver nitrate for halide ions; and dilute hydrochloric acid with barium chloride for sulfate ions. By combining results, you identify the compound. For example, a compound giving a lilac flame and a white precipitate with barium chloride contains potassium and sulfate ions, so it is potassium sulfate. The compound is single, so one cation and one anion are present.
Revise SulfatesRequired practical 8: analysis and purification of water samples from different sources, including pH, dissolved solids and distillation.
In this required practical, students analyse water samples from different sources and purify one sample by distillation. Analysis includes measuring pH using universal indicator or a pH meter, and determining dissolved solids by evaporating a measured volume of water and weighing the residue. Distillation involves heating the water sample so that water vaporises, leaving dissolved solids behind, and then condensing the vapour to collect pure water. Students record observations, compare samples and explain how results show differences in water quality. A larger residue after evaporation indicates more dissolved solids. The practical develops skills in accurate measurement, safe heating and separation techniques.
Revise Potable water
Exam board practical handbooks & guides
Official practical documents published by AQA for this qualification.
- Open official PDF
Practical handbook: GCSE Chemistry
Practical handbook
Practise the questions examiners set on these practicals.
A week of Premium from your first lesson · Then the free plan continues · No card, no charge