Transport in and out of cells — OCR GCSE Biology
Transport in and out of cells explained
Transport in and out of cells covers 2 specification points, including Use of appropriate apparatus and techniques… and Use of appropriate apparatus to make and….
Read the full explanation
Open a point below for its explanation and revision guidance.
Use of appropriate apparatus and techniques for the observation and measurement of biological changes and/or processes
Osmosis is investigated by tracking mass changes in plant tissue (such as potato cylinders) immersed in a range of sucrose concentrations (e.g. 0.0, 0.2, 0.4, 0.6, 0.8, and 1.0 mol/dm³). Cylinders are excised using a cork borer and trimmed to equal lengths on a ceramic tile using a scalpel. Cylinders are weighed on a two-decimal-place electronic balance before immersion. After incubating in sealed boiling tubes for at least 45 minutes, cylinders are removed, rolled gently on a paper towel to remove surface water without squeezing tissue, and reweighed. Percentage change in mass is calculated: ((final mass - initial mass) / initial mass) multiplied by 100, accounting for variation in initial cylinder sizes.
Use of appropriate apparatus to make and record a range of measurements accurately, including length, area, mass, time, temperature, volume of liquids and gases, and pH
Accurate osmosis data requires high-precision instrumentation across multiple variables. Plant cylinders are cut to identical length using a millimetre ruler, standardizing surface area. Masses are recorded to 0.01 g using an electronic balance. Volumes of sucrose solutions are dispensed using a 25 cm³ graduated cylinder or 20 cm³ syringe. Immersion duration is timed with a digital stopwatch. When percentage change in mass is plotted against sucrose concentration, a smooth line of best fit is drawn. The point where the curve intersects the horizontal axis (0% change in mass) identifies the isotonic point, where the external sucrose concentration equals the internal solute concentration of the plant cells.
Your focus
- Prepare uniform potato cylinders using cork borers and scalpels, controlling surface area to volume ratio.
- Execute standardized blotting and weighing procedures to determine initial and final tissue mass.
- Calculate percentage change in mass and explain why it provides a valid basis for comparing biological samples.
Show all 6 objectives
- Record tissue mass to 0.01 g precision and dispense accurate solution volumes using syringes or measuring cylinders.
- Construct graphs of percentage mass change against concentration with correct axes, scales, and lines of best fit.
- Determine the internal solute concentration of plant tissue by interpolating the isotonic crossing point on the x-axis.
Transport in and out of cells exam tips
Marking Points
- Cut uniform plant tissue cylinders using a cork borer and trim to equal dimensions using a scalpel and ruler.
- Blot cylinders gently on a paper towel to remove excess surface liquid before taking initial and final mass readings.
- Calculate percentage change in mass using the formula: ((final mass - initial mass) / initial mass) × 100.
- Explain why calculating percentage change in mass is necessary: it standardizes results to account for small differences in initial mass.
- Record tissue masses to two decimal places (0.01 g) using a tared electronic balance.
- Measure solution volumes accurately using a graduated syringe or measuring cylinder to ensure complete tissue immersion.
- Plot percentage change in mass on the y-axis against sucrose concentration on the x-axis, drawing a smooth line of best fit.
- Determine the isotonic concentration (internal cell solute concentration) by identifying where the line of best fit crosses the x-axis (0% mass change).
Examiner Tips
- 💡Always explain why percentage change in mass is calculated: 'because the starting masses of the potato cylinders were not identical'.
- 💡Be prepared to explain why cylinders gain mass in dilute solutions (water enters by osmosis down a water potential gradient) and lose mass in concentrated solutions.
- 💡The point where the line of best fit crosses the x-axis represents the concentration where there is no net movement of water by osmosis.
- 💡When asked what happens to cells at the isotonic point, state: 'water enters and leaves the cells at equal rates, so there is no net osmosis'.
Common Mistakes
- Calculating raw change in mass instead of percentage change in mass, preventing fair comparison between cylinders of different initial masses.
- Squeezing potato cylinders while drying them with a paper towel, forcing intracellular water out and creating false mass loss.
- Leaving test tubes unstoppered, allowing water evaporation which increases sucrose concentration during the experiment.
- Drawing dot-to-dot lines instead of a smooth curve or straight line of best fit through the plotted data points.
- Forgetting that percentage mass change can be negative, misplotting mass loss points above the zero axis.
- Reading the isotonic point inaccurately by misinterpreting axis scale divisions on the graph.